Sony XVS-7000 Users Guide - Page 122

• On the cross-point control block in key/AUX bus delegation mode, press the [DME UTIL1] button in the 1st row and select a signal using the cross-point buttons in the 2nd row. Notes • You can assign the DME utility 1 bus using the [UTIL] button on the cross-point pad of the crosspoint control block (see page 79). • You can assign a DME utility 1 bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). Using four DME channels on one keyer 1 In the group of the M/E-1 >Key1 >Processed Key menu (1116), select consecutive DME channels. Select [DME1] for the first channel, [DME2] for the second channel, [DME3] for the third channel, and [DME4] for the fourth channel. 2 Select the second channel video signal. Select using any of the following methods. • On the cross-point control block, press delegation button [DME EXT] on the cross-point pad and select a signal using the cross-point buttons. • On the cross-point control block in key/AUX bus delegation mode, press the [DME EXT] button in the 1st row and select a signal using the cross-point buttons in the 2nd row. Notes • You can assign the DME external video bus using the [UTIL] button on the cross-point pad of the cross-point control block (see page 79). • You can assign a DME external video bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). 3 Select the third channel video signal. Select using any of the following methods. • On the cross-point control block, press delegation button [DME UTL1] on the cross-point pad and select a signal using the cross-point buttons. • On the cross-point control block in key/AUX bus delegation mode, press the [DME UTIL1] button in the 1st row and select a signal using the cross-point buttons in the 2nd row. Notes • You can assign the DME utility 1 bus using the [UTIL] button on the cross-point pad of the crosspoint control block (see page 79). • You can assign a DME utility 1 bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). 4 Select the fourth channel video signal. Select using any of the following methods. • On the cross-point control block, press delegation button [DME UTL2] on the cross-point pad and select a signal using the cross-point buttons. • On the cross-point control block in key/AUX bus delegation mode, press the [DME UTIL2] button in the 1st row and select a signal using the cross-point buttons in the 2nd row. Notes • You can assign the DME utility 2 bus using the [UTIL] button on the cross-point pad of the crosspoint control block (see page 79). • You can assign a DME utility 2 bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). To check DME usage status You can check the DME operating status in the Status >DME Status menu (3311) (see page 192). Assigning a DME output signal as a monitor signal 1 In the M/E-1 >Key1 >Processed Key menu (1116), press [Monitor]. The Monitor menu (1116.1) appears. 2 Press [Monitor Set], turning it on. 3 In the group, select the DME channel (DME1 to DME4) to be used. This assigns the selected DME output to DME MON V and DME MON K. The lit colors of [DME1] to [DME4] indicate the DME assignment. Lit green: DME currently being monitored Lit amber: DME which can be monitored Not lit: Unassigned DME 122