Sony XVS-7000 Users Guide - Page 210

• Logical switcher 2: !L_SWR2 Only folders and files in the dedicated folder are displayed as the target for operations in the menu for each logical switcher. Notes • In dedicated mode, up to 2-level hierarchy folders are supported using frame memory. • When resource sharing is enabled, the dedicated folder of the logical switcher is not displayed in the menu. Only folders and files in the dedicated folder are displayed. When resource sharing is disabled, the dedicated folder is also displayed in the menu, and folder and file operations are supported. Note that it is not possible to lock the dedicated folder. • If the same file structure is used in the dedicated folders for logical switchers 1 and 2, frame memory operations on both logical switchers are linked when Dual Simul mode is set. Frame memory outputs Frame memory outputs (FM1 to FM20) are assigned to logical switchers 1 and 2 in groups of four channels. Sharing is supported when the signal formats of logical switchers 1 and 2 are the same. Shared frame memory output restrictions Shared FM outputs have the following restrictions. • On logical switcher 2, only the selection of cross-points of FM outputs is available. Other FM output operations are not available. • Logical switcher 1 information is linked to and displayed on the FM output button in the Frame Memory menu of logical switcher 2 (excludes audio data and lock setting). • During clip creation (recording), the FM output button in the Frame Memory menu is displayed as follows. Logical switcher 1: Thumbnail is black, and "Recording" is displayed. Logical switcher 2: Thumbnail is black, and "Through" is displayed. • When a frame memory folder is set to dedicated mode and a shared FM output is selected, the thumbnail for files are not displayed in the Frame Memory menu of logical switcher 2. • Frame memory output signals Signals selected on frame memory outputs assigned to logical switcher 2 can be used on logical switcher 1. • Switcher bank output signals (re-entry signals) Switcher bank output signals on logical switcher 2 can be used on logical switcher 1. Notes • Enabled only when logical switcher 1 signal format is 3840×2160P 2SI or 3840×2160P SQD, and logical switcher 2 signal format is 1080P. • On the XVS-8000/7000/6000, internal format converter resources must be assigned to logical switcher 1. On the XVS-9000, internal format converter resources are automatically assigned to logical switcher 1. Set the internal format converters and cross-points on logical switcher 1. Internal format converter settings • Set the FC channels of internal format converters for use as inputs (XVS-8000/7000/6000 only) • Set logical switcher 2 signals as format converter input signals. The following logical switcher 2 signals can be selected. - L2 FM1 to L2 FM4: Frame memory outputs - L2 P/P Out1 to L2 P/P Out6, L2 M/E-x Out1 to L2 M/E-x Out6 (x = 1 to 5): Switcher bank output signals On the XVS-9000, signals can be assigned to FC channels using the Engineering Setup >Switcher >Input >Internal FC >Internal FC Re-Entry Select menu (7332.11) (see page 210). On the XVS-8000/7000/6000, signals can be assigned to FC channels using the Engineering Setup >Switcher >Input >Internal FC >FC Input Select menu (7332.3) (see page 445). • Set the format converter input signal format to 1080P (XVS-8000/7000/6000 only). Cross-point settings • Assign the FC channels with the configured logical switcher 2 signals to the cross-point buttons. You can select a format-converted logical switcher 2 signal on logical switcher 1 by pressing the cross-point button assigned with the corresponding FC channel. Leveraging Resources using Resource Sharing Signals on logical switcher 2 can be configured for selection as input signals on logical switcher 1 by using the resource sharing and internal format converter functions. The following logical switcher 2 signals can be used on logical switcher 1. Setting XVS-9000 internal format converter inputs When an XKS-8460 Format Converter Board is installed in the XVS-9000, the internal format converters can be configured on logical switcher 1 when resource sharing is enabled. 210