Sony XVS-7000 Users Guide - Page 67

g OUTPUT connectors (BNC type: XKS-S8165/ XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) XVS-8000/7000: 1 to 48 connectors XVS-6000: 1 to 24 connectors Any outputs, such as program outputs, preview outputs, and AUX outputs, can be assigned and output as serial digital video signals. The output setting is controlled from the control panel of the XVS system. The number of connectors (slots) available depends on the number of option connector boards installed. h OUTPUT 49 to 52 connectors (BNC type: XKS-S8165/XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) If an XKS-S8165 is installed in the XVS-8000, these can be used as output connectors to connect to dedicated inputs. i FC (format converter) OUTPUT 1 to 16 connectors (BNC type: XKS-S8165/XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) Outputs signals generated using the internal format converter function. Up to 16 output systems are supported. The output setting is controlled from the control panel of the XVS system. j SPARE 1 to 4 connectors (BNC type: XKS-S8165/ XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) On the XVS-8000, the same signals on the FC OUTPUT 1, 5, 9, and 13 connectors are output, from left to right, on the SPARE 1, 2, 3, and 4 connectors. On the XVS-7000, the same signals on the FC OUTPUT 1 and 5 connectors are output on the SPARE 1 and 2 connectors. Signals are not assigned to the SPARE 3 and 4 connectors. k MV (multi viewer) OUTPUT 1 to 8 connectors (BNC type: XKS-S8165/XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) Multiple output signals can be combined and output as serial digital video signals arranged in a grid. Up to two output systems are supported. The output setting is controlled from the control panel of the XVS system. l SPARE 5 to 8 connectors (BNC type: XKS-S8165/ XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) Reserved for future use. m OUTPUT 25 to 32 connectors (BNC type: XKS-S8165/XKS-S8167, RJ-45 type: XKS-T8165, QSFP+ type: XKS-Q8166, QSFP28 type: XKS-C8166) Used as multi viewer output 1 to 8 connectors on the XVS-6000. Multiple output signals can be combined and output as serial digital video signals arranged in a grid. Up to two output systems are supported. The output setting is controlled from the control panel of the XVS system. n -AC IN (AC power input) connectors (3-pin) XVS-9000: A, B, C, D, E, and F connectors XVS-8000/7000: A, B, C, and D connectors XVS-6000: A and B connectors Connect to 100 V to 240 V AC power supply with AC power cords (sold separately). o U (signal ground) terminal Connect to the system ground. p MVS LAN (multi format video switcher LAN) connector (RJ-45 compliant) Connect to an Ethernet switch. 1) Used to communicate between switcher control stations connected to an Ethernet switch. 1) For details about supported Ethernet switches, contact your Sony service or sales representative. For details about Ethernet switch connection, refer to the XVS-9000/8000/ 7000/6000 Installation Manual. q UTL LAN (utility LAN) connector (RJ-45 compliant) Reserved for future use. Do not connect any signal to this connector. r GPI connector (D-sub 25-pin) Outputs an alarm when a switcher error occurs. s RESET CIRCUIT BREAKER buttons If an overcurrent condition is detected, due to a short circuit or other cause, the button will pop out, disconnecting the circuit. The button pops out approximate 3.5 mm (5/32 inches). t REF IN (reference video signal input) connectors (BNC type) Connect to an HD tri-level sync signal, black burst signal, or analog sync signal when using the unit synchronized to an external sync signal. The two connectors are loop-through, so that the signal input on either connector is also output on the other connector. Connect the supplied 75 Ω terminator to the remaining connector if not using the loop-through output. 67