Sony XVS-7000 Users Guide - Page 68
About 4K signal input/output connector, assignment SDI connector boards
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 68 highlights
About 4K signal input/output connector assignment (SDI connector boards) In 4K format, a subdivided-by-4 image (sub images) are transferred as four separate signals, where the 4K signal is assigned to four input/output connectors. On connector boards that support 12G-SDI,1) a 4K signal can be transferred using a single cable. 1) 12G-SDI is an interface for digital transfer of 4K signals using a co-axial cable that supports 12 Gbps transfer speeds. When assigning to four connectors On the following connector boards, a 4K signal is assigned to a group of four connectors. • Input connector boards: XKS-S8110/XKS-S8111 • Output connector boards: XKS-S8165 The assignment is as follows. 4K format input signal/ output signal 1st system 2nd system 3rd system (and so on) Connector number a) 1, 2, 3, 4 5, 6, 7, 8 9, 10, 11, 12 (and so on) a) The connector numbers correspond to sub images 1, 2, 3, and 4 in that order. Note On connector boards that support 12G-SDI (XKS-S8112/ XKS-S9112/XKS-S8167/XKS-S9167), four signals are transferred in the following cases. • For input/output of 3840×2160P 2SI 3G, 3840×2160P SQD, and 3840×2160PsF SQD signals • When the XKS-S8167 output connectors are set to 3G mode When assigning to one connector (12G-SDI) On the following connector boards, a 4K signal (3840×2160P 2SI 12G) is assigned to a single connector. • Input connector boards: XKS-S8112/XKS-S9112 • Output connector boards: XKS-S8167/XKS-S9167 The assignment is as follows. 4K format input signal/ output signal 1st system 2nd system 3rd system (and so on) Connector number XKS-S8112/ XKS-S9112/ XKS-S8167 XKS-S9167 1 1 5 3 9 5 (and so on) (and so on) Notes • The XKS-S8112/XKS-S8167 use the input connectors/ output connectors with the first number (1, 5, 9, and so on) of each group of four connectors. • The XKS-S9112/XKS-S9167 use the input connectors/ output connectors with odd numbers (1, 3, 5, and so on). About output connectors of 12G-SDI connector boards The output connectors of the XKS-S8167/XKS-S9167 12G-SDI Output Boards can be enabled/disabled. When disabled, no signal is output from the output connector. If a cable is not connected to an enabled output connector, radio wave interference may occur. Disable unused output connectors. For details, see "Enabling/Disabling SDI Output Connectors" (page 404). Note On the XVS-9000, when the switcher signal format is 3840×2160P 2SI, if the signal format of the odd-numbered output connectors on the XKS-S9167 is set to 3840×2160P 2SI 12G, a signal converted to 1080i format is output on the subsequent even-numbered output connectors. About network connector boards The XKS-C8111/XKS-C9111/XKS-C9111N/ XKS-C9121/XKS-C9121N/XKS-C8166 have the following restrictions. • Two slots per board are required for the installation of XKS-C9111/XKS-C9111N/XKS-C9121/ XKS-C9121N. • The XKS-C9111/XKS-C9121 and XKS-C9111N/ XKS-C9121N cannot be installed at the same time. • The XKS-C9121/XKS-C9121N supports both inputs and outputs (bidirectional). • On the XKS-C9111N/XKS-C9121N, input/outputs 7 and 15 on each board cannot be used. The XKS-C9111N/XKS-C9121N support 3840×2160P 2SI signal format. Accordingly, odd-numbered input/ outputs can be configured, but input/outputs that are multiples of 8 minus 1 (7, 15, 23, and so on) are invalid. • The XKS-C8111/XKS-C8166 cannot be installed at the same time as the XKS-T8110/XKS-T8165. 68