Sony XVS-7000 Users Guide - Page 446
Assigning an input signal to an FC channel, Setting the conversion format
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 446 highlights
• On the XVS-7000, FC9 to FC16 cannot be used. • In 4K format, only FC1, FC5, FC9, and FC13 can be configured. Assigning an input signal to an FC channel You can assign a signal to be converted by the format converter to an FC channel. 1 In the Engineering Setup >Switcher >Input menu (7332), press [Internal FC]. The Internal FC menu (7332.5) appears. 2 Press [FC Input Select]. The FC Input Select menu (7332.3) appears. The status area shows the FC channel list on the left and the list of input signals that can be assigned to FC channels on the right. 3 In the list on the left, select the target FC channel to set. 4 In the list on the right, select an input signal. 5 Press [Set]. To set the source name of the converted input signal 1 Select the target FC channel to set, and press [FC Name]. 2 Enter a name of up to 16 characters in the keyboard window, and press [Enter]. Setting the conversion format You can set the signal format of inputs to convert by the format converter. The conversion format is set in the following groupings, depending on the switcher signal format. • 3840×2160P, 1080P: 4-channel groups (FC1 to FC4, FC5 to FC8, FC9 to FC12, FC13 to FC16) • 1080i, 720P: 8-channel groups (FC1 to FC8, FC9 to FC16) Notes • When the switcher signal format is 3840×2160PsF or 1080PsF, input signal format conversion is not available. • When the switcher signal format is 1080P, the signal formats that can be converted vary depending on the 720P converter setting. For details about the 720P converter, see "Enabling/ disabling the 720P converter" (page 459). • On an internal format converter, the format of only the XKS-S8110 SDI Input Connector Board input signals can be converted. Supported formats The supported conversion formats are given below. Note Field frequency and frame frequency conversion is not supported. Switcher signal format 3840×2160P (Level A, 2SI) 3840×2160P (Level A, SQD) 1080P (Level A) 1080i 720P Input signal format • 3840×2160P (Level A, 2SI) a) • 3840×2160P (Level B, 2SI) • 3840×2160P (Level A, SQD) • 3840×2160P (Level B, SQD) • 1080P (Level A) • 1080P (Level B) • 1080i • 3840×2160P (Level A, 2SI) • 3840×2160P (Level B, 2SI) • 3840×2160P (Level A, SQD) a) • 3840×2160P (Level B, SQD) • 1080P (Level A) • 1080P (Level B) • 1080i • 1080P (Level A) a) • 1080P (Level B) b) • 1080i b) • 720P c) • 1080i a) • 720P • 576i d) • 480i d) • 1080i • 720P a) • 576i d) • 480i d) a) Input signal without format conversion b) Selectable when the 720P converter is disabled c) Selectable when the 720P converter is enabled d) When the switcher signal format frequency is 59.94, only 480i is selectable. When the frequency is 50, only 576i is selectable. 1 In the Engineering Setup >Switcher >Input menu (7332), press [Internal FC]. The Internal FC menu (7332.5) appears. 2 Press [FC Format]. The FC Format menu (7332.6) appears. The status area shows the FC channel list on the left and the supported conversion signal format list on the right. 3 In the list on the left, select the target FC channel to set. Select one of the four target channels or eight target channels to set. 4 In the list on the right, select the signal format. 446