Sony XVS-7000 Users Guide - Page 450
Enabling/disabling an input format, converter, Enabling/disabling the 720P converter
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 450 highlights
Enabling/disabling an input format converter When an XKS-S8111 is installed in the XVS-8000/7000/ 6000, you can enable/disable the format converter function for each input connector board. Notes • For the XKS-S8112/XKS-S9112/XKS-C8111/ XKS-C9111/XKS-C9121, setup is not required. • When the switcher signal format is 3840×2160PsF or 1080PsF, the format converter function is not available. • When the switcher signal format is 1080P, the format converter function is enabled. The signal formats that can be converted vary depending on the 720P converter setting. 1 In the Engineering Setup >Switcher >Input menu (7332), press [Input FC/CCR]. The Input FC/CCR menu (7332.1) appears. 2 Press [FC Format]. The FC Format menu (7332.7) appears. 3 Select the target input connector board to set. No. Parameter Adjustment 1 Group No Input group number a) a) Inputs on an input connector board form a group. 4 In the group, select one of the following. Enable: Enable the format converter function. Disable: Disable the format converter function. To clear the setting Press [Clear]. 5 Press [Execute]. 6 Check the message, then press [Yes]. Note It may take a few minutes until the configuration is completed. Enabling/disabling the 720P converter On an XKS-S8111, when the switcher signal format is 1080P, you can enable/disable the 720P converter. The following conversion formats can be selected depending on the 720P converter setting. • When the 720P converter is disabled: 1080P (Level A), 1080P (Level B), 1080i • When the 720P converter is enabled: 1080P (Level A), 720P Note For the XKS-S8112/XKS-S9112/XKS-C8111/ XKS-C9111/XKS-C9121, setup is not required. 1 In the Engineering Setup >Switcher >Input >Input FC/ CCR menu (7332.1), press [FC Format]. The FC Format menu (7332.7) appears. 2 Select the target input connector board to set. No. Parameter Adjustment 1 Group No Input group number a) a) Inputs on an input connector board form a group. 3 Press [720P Converter] to enable/disable the 720P converter. To enable, press [720P Converter], turning it on. To disable, press [720P Converter], turning it off. To clear the setting Press [Clear]. 4 Press [Execute]. 5 Check the message, then press [Yes]. Note It may take a few minutes until the configuration is completed. Setting the conversion format You can set the signal format of inputs to convert by the format converter. The conversion format is set in the following groupings, depending on the switcher signal format. • XKS-S8111 - 3840×2160P, 1080P: Groups of 4 inputs - 1080i, 720P: Groups of 8 inputs • XKS-S8112 - 3840×2160P, 1080P, 1080i, 720P: Groups of 4 inputs • XKS-S9112 - 3840×2160P 2SI or 3840×2160P SQD, and the conversion format is 3840×2160P 2SI 12G, 1080P, 1080i: Groups of 2 inputs 1) - 3840×2160P 2SI or 3840×2160P SQD, and the conversion format is 3840×2160P 2SI 3G, 3840×2160P SQD: Groups of 4 inputs - 1080P, 1080i, 720P: Groups of 4 inputs 450