Sony XVS-7000 Users Guide - Page 81
Inhibiting Operation of Cross-point, Buttons, Signal Name Display
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 81 highlights
For details, see "Setting the AUX Bus Operation Mode" (page 417) and "Setting the [SHIFT] button operation mode" (page 414). When the [2ND DELG] button is not lit The bus selected by the delegation buttons in the 1st row or 2nd row is assigned to the 3rd row and 4th row. In the case of a 36-button layout, the button numbers are as follows. Button row Button 1st row, 3rd row From left side to 35th 2nd row, 4th row 36th From left side to 35th 36th Button number/ [SHIFT] button 1 to 35 While the [SHIFT] button is held down: 36 to 70 [SHIFT] button (hold mode) 36 to 70 [SHIFT] button (always lit) The [SHIFT] buttons in the 1st row and 3rd row operate in hold mode, and you can select a signal on the shifted state of a button while pressing the [SHIFT] button. The [SHIFT] buttons on the 2nd row and 4th row are always lit, and have no effect when pressed. Inhibiting Operation of Cross-point Buttons Inhibiting operation of each cross-point button For each cross-point button, you can temporarily inhibit operations. Note This setting is cleared when you reset the control panel. To enable inhibit setting operation, assignment to the [XPT INHBT SET] button and [XPT INHBT ALLCLR] button in the cross-point pad is required in the Setup menu. For details, see "Assigning a function to a cross-point pad button" (page 433). Buses for which operations can be inhibited You can specify the cross-point button rows in the crosspoint control block. For example, if you inhibit one cross-point button in the cross-point control block, this inhibits operation of all cross-point buttons with the same number in the following buses. • Background A and background B buses • Key 1 bus to key 8 bus • Utility 1 bus and utility 2 bus • DME utility 1 bus and DME utility 2 bus • DME external video bus Setting inhibit for a cross-point button Press and hold the [XPT INHBT SET] button, and press the target cross-point button to inhibit. While the [XPT INHBT SET] button is pressed, the inhibited buttons flash amber. Notes • Nothing is displayed on inhibited cross-point buttons. • Even when you inhibit operation of a cross-point button, macro attachment settings are still possible. Releasing inhibit mode for a cross-point button Press and hold the [XPT INHBT SET] button, and press the target cross-point button to release. Releasing inhibit mode for all buttons Press and hold the [XPT INHBT SET] button, and press the [XPT INHBT ALLCLR] button. Inhibiting (protect) operation of each cross-point button row For each cross-point button row on the cross-point control block, you can temporarily inhibit button operations. The [ROW-1 PROT] to [ROW-4 PROT] buttons used for protecting rows are assigned to the cross-point pad in the Setup menu (see page 433). Press the [ROW-1 PROT] to [ROW-4 PROT] buttons, turning them on, to inhibit button operation in the target cross-point button rows (1st row to 4th row). Signal Name Display You can attach a name (source name) to the signal assigned to a cross-point button, with a maximum of 16 characters. The specified source name appears on the display of the cross-point control block or AUX bus control block (AUX bus operation mode). There are six display modes, depending on the information to display and format, switched using the display mode buttons on the cross-point pad. For details about the display, see "Cross-Point Control Block" (page 22) and "AUX Bus Control Block" (page 46). Note When a signal on the shifted state of a cross-point button is selected, the shifted signal name is displayed. 81