Sony XVS-7000 Users Guide - Page 158

• 2651, 2652 You can move the pattern for each channel, or for two channels simultaneously depending on the relative values from the current positions (see page 162). • 2801 to 2804, 2811 to 2814 You can set the vertical position as the brick slides in. • 2851 to 2854, 2861 to 2864 You can set the pattern position for each channel setting when the first transition completes. Pattern limit: You can restrict the range of the transition execution as desired. However, this is not available for an independent key DME wipe. For details, see "Pattern Limit" (page 93). Size: You can set the size of the image. This can only be used when one of the following pattern numbers is selected. • 1201 to 1209, 1221 to 1225, 1251, 2651, 2652, 2851 to 2854, 2861 to 2864, 7201 to 7208, 7221 to 7224 Crop: You can crop the image. It is also possible in 16:9 mode to crop both sides and convert the image to a 4:3 aspect ratio. For the execution of the transition, you can select from the following three options. • Cut • Last 5% • Linear When [Last 5%] is selected, you can set the [Release Transition] as follows. • Last 30% • Last 5% • Off Note When pattern numbers 1701, 1702, 2661, and 2662 are selected, Crop cannot be used. DME Wipe Restrictions Relation to common wipes • DME wipes do not use the wipe generator built into the switcher. Therefore, during the execution of a DME wipe, you can still use a pattern produced by the wipe generator as the source for a pattern key or mask. • A DME wipe pattern cannot be used as the source for a pattern key or mask. Relation to processed keys • When using the DME for a processed key, selecting a DME wipe automatically assigns an available DME for use for DME wipes. If all DMEs are in use, then it is not possible to select a DME wipe. If a DME has been assigned in the Setup menu, that setting takes precedence. For details, see "Setting DME Channel Assignments" (page 441). • It is not possible to use a resizer DME wipe for a key with processed key enabled. Relation to image effect It is not possible to use background DME wipes when an image effect is set. Relation to resizer • When a resizer is enabled, it is not possible to select a DME wipe or resizer DME wipe. • For the key 1 and key 2, key 3 and key 4, key 5 and key 6, or key 7 and key 8 combinations, if one key is used for a dual resizer effect, the other key cannot be used for a DME wipe or resizer DME wipe. Resizer DME wipe restrictions When the screen aspect ratio is 4:3 in HD format, reducing an image using the resizer reduces the 16:9 image as-is with the added image portions on the left and right sides. Use the crop function as required to extract the 4:3 image. Number of DME wipes that can be used on a single M/E bank DME wipes can be used in nine places, including eight independent key transitions. When the switcher signal format is 3840×2160P 2SI, they can be used in three places, including two independent key transitions. Note The number of keys to which DME effects (including DME wipes) can be applied simultaneously for one M/E bank varies as follows depending on the execution mode of the DME wipe pattern selected for the background. Key to which DME effects are applied Keys 1 to 4 Keys 5 to 8 DME wipe pattern for background Number of keys to which DME effects can be applied simultaneously DME wipes not used 2 1-channel mode 1 2-channel or 0 3-channel mode - 2 When the signal format is 3840×2160P 2SI, DME effects (including DME wipes) can be used simultaneously in only one place on an M/E bank. When not using background DME wipes, DME effects can be used on either key 1 or key 2. 158