Home » Sony Manuals » Video Receivers » Sony XVS-7000 » Manual Viewer

Sony XVS-7000 Users Guide - Page 238

Wipe Crop Settings, Flex shadow creation example, Applying the wipe crop effect

Add to My Manuals
Save this manual to your list of manuals

Page 238 highlights

Example 2: Flex Shadow is enabled on one channel only. Video Video Shadow No combine shadow is set. Combine shadow is enabled. Density is set to 100.00. Combine shadow is enabled. Density is set to 0.00. 1 In the Flex Shadow menu (4115), press [Combine Shadow], turning it on. 2 Set the following parameter. No. Parameter Adjustment 1 Density Density of combine shadow Notes • The Combine Shadow effect is applied to all shadows, not only the sections where shadows overlap. • Enabling the Combiner global effect when flex shadow is enabled will enable the Combine Shadow effect. In this state, Combine Shadow remains enabled even if the global effect is disabled. • In Combine Shadow, the setting for the channel with the lowest number among the channels being combined is enabled. Flex shadow creation example This section describes the flex pattern creation flow for the following pattern as an example. 1 In the DME >Edge >Flex Shadow menu (4115), press [Flex Shadow], turning it on. 2 In the group, select [External]. 3 Select [Axis Loc] and set the [Axis Loc V] parameter so that the center of the flex shadow deformation is at the bottom of the picture. (In 16:9 mode: Axis Loc V = -9.00) It is recommended that the operation is performed by displaying the flex shadow center axis by enabling [Flex Shadow Axis] in the DME >Input/Output >Graphic menu (4164). 4 In the group, select [V] to invert the flex shadow vertically. 5 Select [Size] and set the [Size V] parameter so that the shadow extends vertically. (In 16:9 mode: Size V = -1.50) 6 Select [Skew] and set the [Skew H] parameter so that the parallel lines appear to emerge from the rear at the right. (In 16:9 mode: Skew H = -50.00) Wipe Crop Settings Notes • Enabling Wipe Crop disables Mask if it is set. • When Brick is set, Wipe Crop cannot be enabled. Brick must be disabled in order to enable Wipe Crop. Applying the wipe crop effect To select a pattern 1 Open the DME >Edge >Wipe Crop menu (4116). 2 Press [Wipe Crop], turning it on. 3 Press [Pattern Select]. The Pattern Select menu (4116.1) appears. 4 From the displayed patterns (standard wipe patterns 1 to 24 and 304), press any pattern to select it. 238

Section	Page
Table of Contents	4
Chapter 1 Overview	16
Introduction	16
Features	17
Main Functions	18
Chapter 2 Menus and Control Panel	21
Names and Functions of Parts of the Control Panel	21
Names and Functions of Parts of the Menu Screen	52
Basic Menu Operations	59
Power Supply and Connector Section	63
Chapter 3 Signal Selection and Transitions	74
Image Creation Operation Flow	74
Signal Selection	75
Transitions	82
Basic Operation for Transitions	84
Key Priority Settings	86
Transition Type Selection	89
Executing a Transition	91
Transition Preview	98
Independent Key Transitions	99
Fade-to-Black	105
AUX Mix Transitions	105
Chapter 4 Keys	107
Overview	107
Key Setting Operations (Menu)	110
Key Adjustments (Menu)	114
Key Operations (Key Control Block)	124
Key Adjustments (Key Control Block)	126
Resizer	129
Key Snapshots	138
Chapter 5 Wipes	140
Overview	140
Basic Wipe Setting Operations	140
Basic Independent Key Transition Wipe Setting Operations	150
Wipe Snapshots	151
Chapter 6 DME Wipes	154
Overview	154
Basic DME Wipe Setting Operations	159
Basic Independent Key Transition DME Wipe Setting Operations	164
DME Wipe Snapshots	166
Creating User Programmable DME Patterns	166
Chapter 7 Frame Memory	169
Overview	169
Frame Memory Operations	171
Still Image Operations	175
Clip Operations	176
Clip Transitions	179
Editing Folders and Files	180
Chapter 8 Color Backgrounds, Copy and Swap, and Other Settings	183
Color Backgrounds	183
Copy and Swap	185
Register Groups	187
Copying Data Between Control Panels	188
Misc Menu	188
Aux Menu	190
Status Menu	192
Router Menu	193
Video Process	194
Image Effect	195
Chapter 9 Special Functions	196
Side Flags	196
Multi Program 2	199
M/E Configuration Switching (M/E Split)	207
Resource Sharing	207
Chapter 10 DMEs	212
Overview	212
Three-Dimensional Transform Operations	224
Applying Special Effects (Common Operations)	229
Applying Special Effects (Edge Effects)	229
Applying Special Effects (Effects on the Overall Signal)	241
Applying Special Effects (Nonlinear Effect Settings)	248
Applying Special Effects (Lighting/Recursive Effects)	260
Applying Special Effects (Other Effects)	272
Global Effects	275
Chapter 11 External Devices	281
Control of External Devices	281
Control of P-Bus Devices	282
Control of GPI Devices	284
Control of VTRs and Disk Recorders	286
Chapter 12 Keyframes	295
Regions	295
Registers	296
Keyframes	296
Displaying the Timeline Menu	303
Recalling a Register	305
Specifying the Region and Edit Points	307
Creating and Editing Keyframes	308
Time Settings	316
Path Settings	317
Effect Execution	319
Saving Effects	320
Creating and Saving a Master Timeline	321
Recalling and Executing a Master Timeline	323
Editing Registers	324
Chapter 13 Snapshots	327
Overview	327
Snapshot Operations (Numeric Keypad Control Block)	328
Snapshot Operations (Flexi Pad Control Block)	330
Snapshot Operations (Menu)	333
Chapter 14 Utility/Shotbox	337
Utility Overview	337
Utility Execution	337
Shotbox Overview	339
Shotbox Register Creation	340
Shotbox Execution	342
Shotbox Register Editing	344
Chapter 15 Macros	345
Macros	345
Macro Operations (Numeric Keypad Control Block and Utility/Shotbox Control Block)	348
Macro Operations (Flexi Pad Control Block)	353
Macro Operations (Cross-Point Control Block)	357
Macro Operations (Menu)	357
Macro Attachments	362
Menu Macros	367
Macro Timeline	372
Chapter 16 Files	374
Overview of File Operations	374
Operations on Individual Files	375
Batch File Operations	378
Frame Memory File Operations	380
Directory Operations	385
Copying Files Between Unit IDs	386
Chapter 17 System Setup	387
Settings Relating to the Network	387
Settings Relating to System Configuration	393
Settings Relating to Signal Formats	394
Power-On (Startup) State Selection	397
Reset and Initialization	399
Settings Relating to Installation and Devices	400
Settings Relating to Device Management	402
Chapter 18 Control Panel Setup	406
Settings Relating to Control Panel Configuration	406
Cross-Point Settings	413
AUX Bus Control Block Settings	417
Settings Relating to Button Assignment	419
Settings Relating to Device Connections	427
Settings Relating to Operation	428
Settings Relating to Control Panel Management	437
Chapter 19 Switcher Setup	439
Settings Relating to Switcher Configuration	439
Settings Relating to Signal Inputs	443
Settings Relating to Signal Outputs	454
Settings Relating to Video Switching	466
Settings Relating to Keys, Wipes, and Frame Memory	468
Settings Relating to Function Links	469
Settings Relating to Device Connections	471
Chapter 20 DME Setup	472
Settings Relating to Signal Inputs	472
Chapter 21 DCU Setup	473
Parallel Input Settings	473
GPI Input Settings	474
Parallel Output Settings	476
GPI Output Settings	477
Configuring the Connection Port of External Devices	478
Chapter 22 Router Interface and Tally Setup	484
Router Interface Settings	484
Tally Group Settings	486
Wiring Settings	486
Tally Generation Settings	487
Tally Copy Settings	488
Parallel Tally Settings	489
Serial Tally Settings	490
Chapter 23 Diagnostics	492
Control Panel Connection Status	492
Remote Panel Connection Status	493
Appendix	494
Wipe Pattern List	494
Menu Tree	501
Menus Recalled by Pressing a Button Twice	520
XVS-9000/8000/7000/6000 System Configuration Comparison	523
4K Format Restrictions	525
Resource Sharing Configuration Operations	526
File Manager	530
Simple Connection of the MKS-8080/8082 AUX Bus Remote Panel	533
Network AUX Remote Panel	535
Macro File Editing Rules	536
Content Displayed in Macro Attachment List	544
Menu Operations Not Registered in a Menu Macro	547
Data Saved by [Setup Define] and [Init Status Define]	548
Error Messages	552
Maintenance	559

Match case Limit results 1 per page

238

In the Flex Shadow menu (4115), press [Combine

Shadow], turning it on.

Set the following parameter.

•

The Combine Shadow effect is applied to all shadows,

not only the sections where shadows overlap.

•

Enabling the Combiner global effect when flex shadow

is enabled will enable the Combine Shadow effect. In

this state, Combine Shadow remains enabled even if the

global effect is disabled.

•

In Combine Shadow, the setting for the channel with the

lowest number among the channels being combined is

enabled.

Flex shadow creation example

This section describes the flex pattern creation flow for the

following pattern as an example.

In the DME >Edge >Flex Shadow menu (4115), press

[Flex Shadow], turning it on.

In the <Flex Shadow Source> group, select [External].

Select [Axis Loc] and set the [Axis Loc V] parameter

so that the center of the flex shadow deformation is at

the bottom of the picture.

(In 16:9 mode: Axis Loc V = –9.00)

It is recommended that the operation is performed by

displaying the flex shadow center axis by enabling

[Flex Shadow Axis] in the DME >Input/Output

>Graphic menu (4164).

In the <Invert> group, select [V] to invert the flex

shadow vertically.

Select [Size] and set the [Size V] parameter so that the

shadow extends vertically.

(In 16:9 mode: Size V = –1.50)

Select [Skew] and set the [Skew H] parameter so that

the parallel lines appear to emerge from the rear at the

right.

(In 16:9 mode: Skew H = –50.00)

Wipe Crop Settings

•

Enabling Wipe Crop disables Mask if it is set.

•

When Brick is set, Wipe Crop cannot be enabled. Brick

must be disabled in order to enable Wipe Crop.

Applying the wipe crop effect

To select a pattern

Open the DME >Edge >Wipe Crop menu (4116).

Press [Wipe Crop], turning it on.

Press [Pattern Select].

The Pattern Select menu (4116.1) appears.

From the displayed patterns (standard wipe patterns 1

to 24 and 304), press any pattern to select it.

No.

Parameter

Adjustment

Density

Density of combine shadow

Notes

No combine shadow is set.

Video

Shadow

Combine shadow is enabled.

Density is set to 100.00.

Combine shadow is enabled.

Density is set to 0.00.

Example 2: Flex Shadow is enabled on one channel only.

Notes