Sony XVS-7000 Users Guide - Page 49

Button name a) Description NEXT (>> XXX) Displays the next page of the crosspoint pad. XXX = page name (up to 12 characters) Row-n Assign Status (XXX) Displays the bus/function names assigned to the 1st row to 4th row. n = 1 to 4 XXX = bus/function name b) Current Page Status (PAGE 1 XXX to PAGE14 XXX) Displays the name of the currently displayed page. XXX = page name (up to 12 characters) Disp Mode Status (DISP: XXX) Displays the name of the currently set display mode. XXX = display mode name (up to 12 characters) Macro Reg Status (MACRO: XXX, ATTCH: XXX) Displays the name of the currently recalled macro register. Displays the macro attachment register name while the [PRE MACRO] button or [POST MACRO] button is pressed. XXX = macro register name (up to 8 characters) DISP MODE1 to DISP MODE6 (XXX) Selects display mode 1 to 6 (display mode button). XXX = display mode name (up to 12 characters) RTR MODE Switches to router operation mode. 2ND DELG Sets second delegation mode. DEST DISP MODE AUX MIX c) 2ND AUX MIX c) (AUX MIX) XPT HOLD c) 2ND XPT HOLD c) (XPT HOLD) Switches the 1st row and 2nd row information shown on the display to the selected signal/source names. • Executes an AUX mix transition on the 3rd row when the [2ND DELG] button is lit. • Executes an AUX mix transition on the 3rd row or 4th row when the [2ND DELG] button is not lit. Executes an AUX mix transition on the 4th row when the [2ND DELG] button is lit. • Sets cross-point hold on the 3rd row when the [2ND DELG] button is lit. • Sets cross-point hold on the 3rd row and 4th row when the [2ND DELG] button is not lit. Sets cross-point hold on the 4th row when the [2ND DELG] button is lit. Button name a) KEY c) 2ND KEY c) (KEY) Description • You can select a signal on the key side of the 3rd row while pressing the [KEY] button when the [2ND DELG] button is lit. • You can select signals on the key side of the 3rd row and 4th row while pressing the [KEY] button when the [2ND DELG] button is not lit. You can select a signal on the key side of the 4th row while pressing the [KEY] button when the [2ND DELG] button is lit. LEVEL BTN1 to LEVEL BTN4 d) Selects the S-Bus/NS-Bus level configured in the Setup menu (level selection buttons). XPTPAD COPY Copies the cross-point pad settings. ROW-n P/P OUT1 c) ROW-n M/E-1 OUT1 to ROW-n M/E-5 OUT1 c) (XXX) Loads images (OUT1) from the PGM/PST and M/E-1 to M/E-5 banks into the 3rd row or 4th row (re-entry buttons). n = 3 or 4 XXX = Name set to P/P OUT1, M/E-1 OUT1 to M/E-5 OUT1 ROW-n P/P OUT6 c) ROW-n M/E-1 OUT6 to ROW-n M/E-5 OUT6 c) (XXX) Loads images (OUT6) from the PGM/PST and M/E-1 to M/E-5 banks into the 3rd row or 4th row (re-entry buttons). n = 3 or 4 XXX = Name set to P/P OUT6, M/E-1 OUT6 to M/E-5 OUT6 MACRO TAKE (TAKE) Executes a macro take operation. Macro Status (EVENT XX/XX) Displays the macro status. XX/XX = executed event number / total number of events Macro: XXX (XXX) Recalls a macro register (1 to 250). XXX = macro register name (up to 8 characters) a) Button name when setting in the Setup menu. When the display differs from that on the cross-point pad, the button name shown in parentheses ( ) is displayed. b) If a destination is selected for which operation is inhibited using the S-Bus/ NS-Bus protect function, "PROT" is displayed in the 3rd row and 4th row. c) Enabled in AUX bus operation mode only. d) Enabled in router operation mode only. Router operation mode Used for destination source selection. The AUX bus control block switches to router operation mode when the [RTR MODE] button on the cross-point pad is pressed, turning it on. a Button rows The 1st row/2nd row are used as destination selection delegation button rows, and the 3rd row/4th row are used as source selection cross-point button rows. 49