Sony XVS-7000 Users Guide - Page 125
Selecting a Key Fill, When key wipe pattern key is selected
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 125 highlights
When key wipe pattern key is selected No. Parameter Adjustment 1 SIZE Pattern size 2 SOFT Degree of edge softness 3 DENSITY Key density • On the cross-point control block, press a key bus delegation button on the cross-point pad and select a signal using the cross-point buttons. • On the cross-point control block in key/AUX bus delegation mode, press a key bus delegation button in the 1st row and select a signal using the cross-point buttons in the 2nd row. Selecting a Key Fill Set a key fill using the key fill/key source selection buttons. When using a color matte Press the [PAGE] button to display the page 2/3 setting buttons, then press the [MAT FILL] button. The [MAT FILL] button turns on green, and displays the parameter name and value of each parameter item on the display. When [Flat Color] is selected in the Type >Matte Adjust menu, set the following parameters. No. Parameter 1 LUM 2 SAT 3 HUE Adjustment Color 1 luminance Color 1 saturation Color 1 hue When [Mix Color] is selected in the Type >Matte Adjust menu, set the following parameters. Parameter group [1/2] No. Parameter 1 LUM 2 SAT 3 HUE 4 SIZE 5 SOFT Adjustment Color 1 luminance Color 1 saturation Color 1 hue Pattern size Degree of softness of pattern edge Parameter group [2/2] No. Parameter 1 LUM 2 SAT 3 HUE 4 SIZE 5 SOFT Adjustment Color 2 luminance Color 2 saturation Color 2 hue Pattern size Degree of softness of pattern edge When using a key fill bus signal Press the [PAGE] button to display the page 2/3 setting buttons, then press the [MAT FILL] button, turning it off. Using any of the following methods, select the key fill signal. Note You can assign a key fill bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). Selecting a Key Source Set a key source using the key fill/key source selection buttons. When using a selected key fill and paired key source signal Press the [AUTO SEL] button, turning it on. When using a signal other than the selected key fill paired signal Press the [SPLT] button, turning it on. Using any of the following methods, select the key source. • On the cross-point control block, press and hold a key bus delegation button on the cross-point pad and select a signal using the cross-point buttons in the 2nd row. • Press and hold the [SPLT] button in the key control block, then select a signal using the cross-point buttons in the 2nd row in the cross-point control block. • On the Flexi Pad control block in key operation mode, press and hold a key delegation button in the memory recall section and select a signal using the cross-point buttons in the 2nd row in the cross-point control block. • On the cross-point control block in key/AUX bus delegation mode, press and hold a key bus delegation button in the 1st row and select a signal using the crosspoint buttons in the 2nd row. Notes • On the cross-point control block in key bus mode or free assign mode, you can select a key fill signal in the 1st row and a key source signal in the 2nd row by pressing and holding the following buttons. - Key bus delegation buttons on the cross-point pad - [SPLT] button on the key control block - Key delegation buttons in the memory recall section on the Flexi Pad control block (key operation mode) • You can assign a key source bus delegation button to the 1st row or 2nd row of the AUX bus control block (AUX bus operation mode) in the Setup menu (see page 417). • To select a video signal, first set the [KEY] button operation mode in the Setup menu (see page 112). 125