Sony XVS-7000 Users Guide - Page 134
CG Border Settings, Setting the border device control block
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 134 highlights
No. Parameter Adjustment 1 Inner Soft Softness of inner edge of border 2 Bound Soft Softness of border boundary To add a beveled color edge 1 In the group, press [Beveled Color Edge]. 2 In the group, select the edges for adjustment. Select [Top], [Left], [Right], or [Bottom]. To adjust all four edges simultaneously, press [All]. 3 Set the following parameters. No. Parameter Adjustment 1 Luminance Luminance 2 Saturation Saturation 3 Hue Hue 4 If setting the softness of the border, press [Border Soft], turning it on. 5 Set the following parameters. No. Parameter Adjustment 1 Inner Soft Softness of inner edge of border 2 Bound Soft Softness of border boundary Setting the border (device control block) You can adjust the border width of the top/bottom/left/ right edges in the device control block (trackball). Note The [BDR/CROP] button must be assigned to the operation buttons beforehand in the Setup menu (see page 411). 1 Enable the resizer as described in steps 1 to 3 in "Reducing, enlarging, rotating, and moving keys (device control block)" (page 131). 2 In the M/E-1 >Key1 >Resizer >Border/Crop menu (1115.1), press [Border], turning it on. 3 In the device control block, press the [BDR/CROP] button, turning it on amber. 4 Adjust the border width using the trackball or Z-ring. • Trackball (horizontal rotation): Adjusts the border width in the X-axis direction (left/right edges). • Trackball (vertical rotation): Adjusts the border width in the Y-axis direction (top/bottom edges). • Z-ring: Adjusts the border width simultaneously in the X-axis and Y-axis directions. The target bank and resizer, and the current parameter and its value, are displayed in the display of the device control block. For details about parameter operations, see "ThreeDimensional Parameter Entry" (page 227). Notes • Pressing the [FINE] button, turning it on, enables fine adjustment of setting values (fine mode). • Pressing the [X], [Y], or [Z] button, turning it on, restricts operation to the selected axis. • For borders, the number of significant digits of the parameter after the decimal point is two. CG Border Settings The resizers of two keys are used for CG border settings. The combination of key pairs used is fixed (keys 1 and 2, keys 3 and 4, keys 5 and 6, keys 7 and 8). The setting operations are performed using keys 1, 3, 5, and 7 only. You can also change the position and size of the image embedded in the border. This section describes making settings using key 1 and key 2 as an example. Notes • This setting is available only when the signal format is 3840×2160P, 1080i. • To change the position and size of the image embedded in the border, clean mode must be enabled on the target key. Enabling the CG border settings using key 1 automatically enables clean mode on both key 1 and key 2. • Inserting key 1 also inserts key 2 in unison. Selecting/ releasing key 1 in a next transition also selects/releases key 2 in unison. Inserting/removing key 2 only and transition operations using key 2 only are not possible. • When a CG border is set, key 1 has the following limitations. - Dual resizer effects are not supported. - Resizer border and crop settings are disabled. - The target of resizer mosaic and defocus settings is fixed to the video signal only. • A CG border cannot be set using key 1 if the state of key 2 is any of the following. - If key 2 is currently inserted or used in a transition. - When key 2 is selected in a next transition. - When the resizer of key 2 is enabled. - When DME wipe is selected for the transition type for key 2. 134