Sony XVS-7000 Users Guide - Page 201
Multi Program 2 Mode Settings, Basic Operation, Entering the software install key first time
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 201 highlights
• Setting the Multi Program 2 data to recall in keyframes and snapshots • Changing the key assignment for program output • Assigning sub bank preview output to buttons • Changing the matrix size to standard • Making settings for keyframe timeline operation • Setting extended re-entry • Out2: Main output signals assignable • Out3, Out4: Main and sub output signals assignable • Out5: Sub output signals assignable • Out6: Sub program output (PGM2) (fixed) For details, see "Assigning the output of each bank in multi-program mode" (page 440). Multi Program 2 Mode Settings (Basic Operation) Entering the software install key (first time only) After installing XZS-9200 (for XVS-9000), XZS-8200 (for XVS-8000), XZS-7200 (for XVS-7000), or XZS-6200 (for XVS-6000) Multi Program 2 Software in the switcher, carry out the following procedure. 1 In the status area of the Engineering Setup >System >Install/Unit Config menu (7316), select SWR1 or SWR2, and press [License]. The License menu (7316.6) appears. 2 Enter the software install key. For details, see "Configuring Settings to Use the Software" (page 400). 3 Turn the switcher off and then on again. Setting the operating mode for a switcher bank Set Multi Program 2 mode for each switcher bank. 1 Open the Engineering Setup >Switcher >Config menu (7331). 2 In the status area, select the target switcher bank. 3 In the group, select [Multi Program2]. 4 Repeat steps 2 and 3 as required, to set the operation mode for all target switcher banks. Assigning output signals for Multi Program 2 mode To assign a signal to an output Use the Engineering Setup >Switcher >Config >M/E Output Assign menu (7331.1). In Multi Program 2 mode, you can assign signals in the following configuration to six outputs (Out1 to Out6). • Out1: Main program output (PGM1) (fixed) Note When M/E split 2M/E mode is set on the XVS-9000, there are four available outputs which can be assigned with signals with the following configuration in Multi Program 2 mode. • Out1: Main program output (PGM1) (fixed) • Out2: Main output signals assignable • Out3, Out4: Main and sub output signals assignable By default, the Out6 output signal on each switcher bank is assigned to the sub re-entry buttons on the cross-point pad (see page 434). To use the sub re-entry buttons in M/E split 2M/E mode, the video/key pair number assignments must be changed to the sub program output (PGM2) signal as shown below. Example: When PGM2 is assigned to Out4 V/K pair number 216 226 236 246 256 266 Video signal P/P OUT4 M/E-1 OUT4 M/E-2 OUT4 M/E-3 OUT4 M/E-4 OUT4 M/E-5 OUT4 Key signal P/P OUT4 M/E-1 OUT4 M/E-2 OUT4 M/E-3 OUT4 M/E-4 OUT4 M/E-5 OUT4 To set the background and key configuration Use the Engineering Setup >Switcher >Config >PGM Config menu (7331.2). The differences from operation in standard mode are as follows. Background configuration: Consists of the following combinations. • Main bank: Clean, Bkgd A, Bkgd B • Sub bank: Sub Clean, Utility 2, Utility 3 Key configuration: Key1 can be enabled only when the background is Clean, Bkgd A, or Bkgd B. For details, see "Setting the output configuration for each bank" (page 440). To set the key preview configuration Use the Engineering Setup >Switcher >Config >K-PVW Config menu (7331.3). The differences from operation in standard mode are as follows. Background configuration: Clean or Sub Clean Key configuration: Key1 can be set to [On] or [Link] only when the background is Clean. 201