Sony XVS-7000 Users Guide - Page 452
Setting the frame delay, Setting the frame synchronizer, To set the frame delay level
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 452 highlights
2 Display the target input to set in the status area. Press [Prev] or [Next] to switch the display in the status area. Pressing [Prev] displays the previous four inputs, and pressing [Next] displays the next four inputs. Pressing [Prev Group] or [Next Group] displays the four inputs of the input connector board installed in the previous slot or next slot, respectively. 3 In the status area, select an input. 4 Set the conversion method. The operation is similar to setting an internal format converter. For details, see "Setting the format converter conversion method" (page 447). Setting the frame delay Notes • On the XKS-C8111/XKS-C9111/XKS-C9121, the frame delay level is set to 1 frame (fixed) when the switcher signal format is 720P. • On the XKS-C8111/XKS-C9111/XKS-C9121 when the frame delay level is set to 2 to 4 frames, a phase shift between the embedded audio/metadata and the video signal occurs. • On the XKS-S8111/XKS-S8112/XKS-S9112 when frame delay is enabled, embedded audio/metadata is not output. To set the frame delay level You can set the frame delay level for each input. 1 In the Engineering Setup >Switcher >Input >Input FC/ CCR menu (7332.1), select the target input to set. To select more than one input, press [Plural] and then select. To select all inputs, press [ALL]. 2 Set the following parameter. No. Parameter Adjustment 3 Frame Delay Delay level a) a) On the XKS-C8111/XKS-C9111/XKS-C9121, a delay of 1 to 4 frames. On the XKS-S8111/XKS-S8112/XKS-S9112, the following delay levels can be configured, depending on the switcher signal format. 3840×2160P, 1080P: 1 to 15 frames 3840×2160PsF, 1080PsF, 1080i: 1 to 8 frames 720P: 1 to 15 frames (set value of 1 to 8 frames when the conversion format is 1080i/576i/480i, with an actual delay that is double the set value) To enable/disable the frame delay You can enable/disable the frame delay for input signals where the signal format is not converted. Notes • On the XKS-C8111/XKS-C9111/XKS-C9121, the frame delay cannot be disabled. • On the XKS-S8111, when the switcher signal format is 1080P and the 720P converter is enabled, the frame delay cannot be disabled. 1 In the Engineering Setup >Switcher >Input >Input FC/ CCR menu (7332.1), select the target input to set. To select more than one input, press [Plural] and then select. To select all inputs, press [ALL]. 2 Press [Frame Delay], and enable/disable the frame delay. To enable, press [Frame Delay], turning it on. To disable, press [Frame Delay], turning it off. Setting the frame synchronizer You can enable/disable the frame synchronizer for each input. When the frame synchronizer is enabled, unsynchronized input signals are synchronized. Note The frame synchronizer cannot be enabled in the following cases. • XKS-S8111 - When the switcher signal format is 3840×2160PsF - When the switcher signal format is 3840×2160P and the format converter is enabled - When the switcher signal format is 1080P and the 720P converter is enabled • XKS-S8112/XKS-S9112 - When the switcher signal format is 3840×2160PsF - When the switcher signal format is 3840×2160P and the conversion format is set to a format other than the switcher signal format - When the switcher signal format is 1080P and the conversion format is set to 720P - When the switcher signal format is 3840×2160P 2SI, the conversion format is 3840×2160P 2SI 12G, and for inputs numbered other than multiples of 4 minus 1 (3, 7, 11, and so on) (XKS-S9112 only) 1 In the Engineering Setup >Switcher >Input >Input FC/ CCR menu (7332.1), select the target input to set. To select more than one input, press [Plural] and then select. To select all inputs, press [ALL]. 2 Press [Frame Sync] to enable/disable the frame synchronizer. To enable, press [Frame Sync], turning it on. To disable, press [Frame Sync], turning it off. 452