Sony XVS-7000 Users Guide - Page 455
M/E dedicated outputs, Multi viewer output connectors settings, Output signal format conversion
View all Sony XVS-7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 455 highlights
Output number 1, 2, 3, 4 5, 6, 7, 8 9, 10, 11, 12 13, 14, 15, 16 (and so on) Setting number 1 5 9 13 (and so on) Note When XKS-S8167 12G-SDI Output Board output connectors are set to 12G mode, 3840×2160P 2SI signals are output as a 12G×1 signal, but the output setting is available only for the first number output in each group of four outputs. M/E dedicated outputs On the XVS-8000, M/E dedicated output connectors 1 to 16 can be used by installing an XKS-S8165 SDI Output Connector Board in slot 2. Two outputs (Ext Out1, Ext Out2) configured on each switcher bank can be assigned to M/E dedicated outputs as output signals. The switcher bank Out1 to Out4 signals can be configured as an Ext Out output signal. For details about M/E dedicated output settings, see "Setting M/E Dedicated Outputs" (page 458). Notes • M/E dedicated outputs are not supported on the XVS-9000/7000/6000. • M/E dedicated outputs are enabled only when the switcher signal format is 3840×2160P. Four M/E dedicated outputs can be used. • The following functions are not available on an M/E dedicated output. Video clips, vertical blanking, through mode, safe titles, 4:3 crop Multi viewer output connectors settings On the XVS-9000, multi viewer output connectors can function as output connectors 81 to 96. You can assign output signals to output connectors 81 to 96 in the same way as other output connectors. To use the connectors as multi viewer output connectors, multi viewer outputs must be assigned to output connectors 81 to 96. For details, see "Assigning Output Signals" (page 456). Output signal format conversion The following format converters can be used. Internal format converter: Configurable when an XKS-8460 Format Converter Board is installed (see page 460). Output format converter: Configurable when an XKS-S9167 12G-SDI Output Board or XKS-C9121 100G IP Input and Output Board is installed (see page 461). P/I converter: Converts a 1080P format signal to 1080i for output (see page 463). Notes • On the XVS-9000, internal format converters and P/I converters are not available. • On the XVS-8000/7000/6000, output format converters are not available. Format converter outputs You can enable the internal format converter function if an XKS-8460 Format Converter Board is installed. Format converter outputs 1 to 16 correspond to format converter channels (FC1 to FC16). You can assign format converter outputs for output to format converter output connectors 1 to 16 or spare connectors 1 to 4 on an output connector board. On the XVS-8000, the number of format converter output connectors will vary depending on the number of output connector boards installed. Spare connectors 1 to 4 can be used if an output connector board for the multi viewer is installed. On the XVS-7000, output connectors 1 to 16 of the output connector boards installed for format converters are used. Spare connectors 1 to 4 can be used if an output connector board for the multi viewer is installed. On the XVS-6000, output connectors 1 to 16 of the output connector boards installed for format converters are used. Spare connectors cannot be used. For details about format converter output connectors and spare connectors, see "XVS-9000/8000/7000/6000 Multi Format Switcher" (page 63). Notes • When using a network connector board (XKS-T8165/ XKS-Q8166/XKS-C8166) for the format converter output, the supported signal formats are restricted. For details about restrictions, see "Network connector board restrictions" (page 454). • When using the format converter output connectors or spare connectors of a network connector board (XKS-T8165/XKS-Q8166/XKS-C8166), the board must be reset after changing the format converter output assignments or output signal conversion format. For details about resetting a board, see "Initializing Network Interface Settings" (page 388). • In 4K format, only FC1, FC5, FC9, and FC13 can be configured. 455