D-Link DGS-3620-52T CLI Guide - Page 124
Optional Specifies the Committed Burst Size. The unit is Kbytes. That is to say, 1
View all D-Link DGS-3620-52T manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 124 highlights
xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide - Enter the profile ID used here. This value must be between 1 and 4. profile_name - Specifies the name of the profile. - Enter the profile name used here. This name can be up to 32 characters long. access_id - Specifies the access ID. - Enter the access ID used here. This value must be between 1 and 128. rate - This specifies the rate for single rate two-color mode. Specify the committed bandwidth in Kbps for the flow. The value m and n are determined by the project. - Enter the rate for single rate two-color mode here. This value must be between 0 and 1048576. burst_size - (Optional) This specifies the burst size for the single rate "two color" mode. The unit is Kbytes. - Enter the burst size value here. This value must be between 0 and 131072. rate_exceed - This specifies the action for packets that exceed the committed rate in single rate "two color" mode. The action can be specified as one of the following: drop_packet - Drop the packet immediately. remark_dscp - Mark the packet with a specified DSCP. The packet is set to have the higher drop precedence. - Enter the remark DSCP value here. This value must be between 0 and 63. tr_tcm - Specify the "two rate three color mode". cir - Specifies the two rate three color mode used. - Enter the two rate three color mode value here. This value must be between 0 and 1048576. cbs - (Optional) Specifies the "Committed Burst Size". The unit is Kbytes. That is to say, 1 means 1Kbytes. This parameter is an optional parameter. The default value is 4*1024. - Enter the comitted burst size value here. This value must be between 0 and 131072. pir - Specifies the "Peak Information Rate". The unit is in Kbps. PIR should always be equal to or greater than CIR. - Enter the peak information rate value here. This value must be between 0 and 1048576. pbs - (Optional) Specifies the "Peak Burst Size". The unit is in Kbytes. - Enter the peak burst size value here. This value must be between 0 and 131072. color_blind - (Optional) Specify the meter mode to be color-blind. The default is color-blind mode. color_aware - (Optional) Specify the meter mode to be color-aware. When this code is specified, user could set the "in-coming packet color" by using command "config color_aware". The final color of packet is determined by the initial color of packet and the metering result. conform - (Optional) Specify the action when packet is in "green color". permit - Permit the packet. replace_dscp - Changes the DSCP of the packet. - Enter the replace DSCP value here. This value must be between 0 and 63. counter - (Optional) Specifies the ACL counter. This is optional. The default is "disable". The resource may be limited so that a counter cannot be turned on. Counters will be cleared when the function is disabled. enable - Specifies that the ACL counter parameter will be enabled. disable - Specifies that the ACL counter parameter will be disabled. exceed - Specify the action when packet is in "yellow color". permit - (Optional) Permit the packet. replace_dscp - Changes the DSCP of the packet. - Enter the DSCP replace value here. This value must be between 0 and 63. drop - Drops the packet. counter - (Optional) Specifies the ACL counter. This is optional. The default is "disable". The resource may be limited so that a counter cannot be turned on. Counters will be cleared when the function is disabled. enable - Specifies that the ACL counter parameter will be enabled. disable - Specifies that the ACL counter parameter will be disabled. violate - Specify the action when packet is in "red color". 119