D-Link DGS-3130 Emulator - Page 56

DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide inner INNER-COS vlan OUTER-VLAN inner INNER-VLAN any host SRC-MAC-ADDR SRC-MAC-ADDR SRCMAC-WILDCARD host DST-MAC-ADDR DST-MAC-ADDR DSTMAC-WILDCARD host SRC-IP-ADDR SRC-IP-ADDR SRC-IPWILDCARD host DST-IP-ADDR DST-IP-ADDR DST-IPWILDCARD precedence PRECEDENCE tos TOS dscp DSCP lt PORT gt PORT eq PORT neq PORT range MIN-PORT MAXPORT TCP-FLAG fragments time-range PROFILENAME ICMP-TYPE ICMP-CODE ICMP-MESSAGE (Optional) Specifies the inner priority value. This value must be between 0 and 7. (Optional) Specifies the outer VLAN ID. (Optional) Specifies the inner VLAN ID. Specifies to use any source MAC address, any destination MAC address, any source IP address, or any destination IP address. Specifies a specific source host MAC address. Specifies a group of source MAC addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to bit value 0 will be checked. Specifies a specific destination host MAC address. Specifies a group of destination MAC addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Specifies a specific source host IP address. Specifies a group of source IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Specifies a specific destination host IP address. Specifies a group of destination IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. (Optional) Specifies that packets can be filtered by precedence level, as specified by a number from 0 to 7. (Optional) Specifies that packets can be filtered by type of service level, as specified by a number from 0 to 15. (Optional) Specifies the matching DSCP code in the IP header. The range is from 0 to 63, or select the following DSCP name: af11 - 001010, af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100, af23 - 010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 - 100010, af42 - 100100, af43 - 100110, cs1 001000, cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000, default - 000000, ef - 101110. (Optional) Specifies to match if less than the specified port number. (Optional) Specifies to match if greater than the specified port number. (Optional) Specifies to match if equal to the specified port number. (Optional) Specifies to match if not equal to the specified port number. (Optional) Specifies to match if falling within the specified range of ports. (Optional) Specifies the TCP flag fields and the specified TCP header bits called ack (acknowledge), fin (finish), psh (push), rst (reset), syn (synchronize), or urg (urgent). (Optional) Specifies the packet fragment's filtering. (Optional) Specifies the name of time period profile associated with the access list delineating its activation period. (Optional) Specifies the ICMP message type. The valid number for the message type is from 0 to 255. (Optional) Specifies the ICMP message code. The valid number for the message code is from 0 to 255. (Optional) Specifies the ICMP message. The following pre-defined parameters are available for selection: beyond-scope, destination-unreachable, echo-reply, echo-request, header, hop-limit, mld-query, mld-reduction, mld-report, nd-na, ndns, next-header, no-admin, no-route, packet-too-big, parameter-option, 52