D-Link DGS-3130 Emulator - Page 58

DGS-3130 Layer 3 Stackable Managed Switch CLI Reference Guide [SEQUENCE-NUMBER] {permit | deny} icmp {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IPWILDCARD} {any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD} [ICMP-TYPE [ICMP-CODE] | ICMP-MESSAGE] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-NAME] [SEQUENCE-NUMBER] {permit | deny} {gre | esp | eigrp | igmp | ipinip | ospf | pcp | pim | vrrp | protocolid PROTOCOL-ID} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-WILDCARD} {any | host DST-IPADDR | DST-IP-ADDR DST-IP-WILDCARD} [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [timerange PROFILE-NAME] [SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-WILDCARD} [any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD] [[precedence PRECEDENCE] [tos TOS] | dscp DSCP] [time-range PROFILE-NAME] Standard IP Access List: [SEQUENCE-NUMBER] {permit | deny} {any | host SRC-IP-ADDR | SRC-IP-ADDR SRC-IP-WILDCARD} [any | host DST-IP-ADDR | DST-IP-ADDR DST-IP-WILDCARD] [time-range PROFILE-NAME] no SEQUENCE-NUMBER Parameters SEQUENCE-NUMBER any host SRC-IP-ADDR SRC-IP-ADDR SRC-IPWILDCARD host DST-IP-ADDR DST-IP-ADDR DST-IPWILDCARD precedence PRECEDENCE dscp DSCP tos TOS lt PORT gt PORT eq PORT neq PORT range MIN-PORT MAXPORT time-range PROFILENAME tcp, udp, igmp, ipinip, gre, esp, eigrp, ospf, pcp, pim, vrrp PROTOCOL-ID Specifies the sequence number. The range is from 1 to 65535. The lower the number is, the higher the priority of the permit/deny rule. Specifies any source IP address or any destination IP address. Specifies a specific source host IP address. Specifies a group of source IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Specifies a specific destination host IP address. Specifies a group of destination IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. (Optional) Specifies that packets can be filtered by precedence level, as specified by a number from 0 to 7. (Optional) Specifies the matching DSCP code in the IP header. The range is from 0 to 63, or select the following DSCP name: af11 - 001010, af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100, af23 - 010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 - 100010, af42 - 100100, af43 - 100110, cs1 001000, cs2 - 010000, cs3 - 011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000, default - 000000, ef - 101110. (Optional) Specifies that packets can be filtered by type of service level, as specified by a number from 0 to 15. (Optional) Specifies to match if less than the specified port number. (Optional) Specifies to match if greater than the specified port number. (Optional) Specifies to match if equal to the specified port number. (Optional) Specifies to match if not equal to the specified port number. (Optional) Specifies to match if falling within the specified range of ports. (Optional) Specifies the name of the time period profile associated with the access list delineating its activation period. Specifies Layer 4 protocols. (Optional) Specifies the protocol ID. The valid value is from 0 to 255. 54